imptcp: Plain TCP Syslog ======================== Provides the ability to receive syslog messages via plain TCP syslog. This is a specialised input plugin tailored for high performance on Linux. It will probably not run on any other platform. Also, it does no provide TLS services. Encryption can be provided by using `stunnel `_. This module has no limit on the number of listeners and sessions that can be used. Multiple receivers may be configured by specifying $InputPTCPServerRun multiple times. **Author:**\ Rainer Gerhards Configuration Directives ------------------------ This plugin has config directives similar named as imtcp, but they all have **P**\ TCP in their name instead of just TCP. Note that only a subset of the parameters are supported. .. function:: $InputPTCPServerAddtlFrameDelimiter This directive permits to specify an additional frame delimiter for plain tcp syslog. The industry-standard specifies using the LF character as frame delimiter. Some vendors, notable Juniper in their NetScreen products, use an invalid frame delimiter, in Juniper's case the NUL character. This directive permits to specify the ASCII value of the delimiter in question. Please note that this does not guarantee that all wrong implementations can be cured with this directive. It is not even a sure fix with all versions of NetScreen, as I suggest the NUL character is the effect of a (common) coding error and thus will probably go away at some time in the future. But for the time being, the value 0 can probably be used to make rsyslog handle NetScreen's invalid syslog/tcp framing. For additional information, see this `forum thread `_. **If this doesn't work for you, please do not blame the rsyslog team. Instead file a bug report with Juniper!** Note that a similar, but worse, issue exists with Cisco's IOS implementation. They do not use any framing at all. This is confirmed from Cisco's side, but there seems to be very limited interest in fixing this issue. This directive **can not** fix the Cisco bug. That would require much more code changes, which I was unable to do so far. Full details can be found at the `Cisco tcp syslog anomaly `_ page. .. function:: $InputPTCPSupportOctetCountedFraming** on|off Defaults to "on", the legacy octed-counted framing (similar to RFC5425 framing) is activated. This is the default and should be left unchanged until you know very well what you do. It may be useful to turn it off, if you know this framing is not used and some senders emit multi-line messages into the message stream. .. function:: $InputPTCPServerNotifyOnConnectionClose on/off Instructs imptcp to emit a message if the remote peer closes a connection. Defaults to off. .. function:: $InputPTCPServerKeepAlive on/off Enable of disable keep-alive packets at the tcp socket layer. The default to off. .. function:: $InputPTCPServerKeepAlive\_probes The number of unacknowledged probes to send before considering the connection dead and notifying the application layer. The default, 0, means that the operating system defaults are used. This has only effect if keep-alive is enabled. The functionality may not be available on all platforms. .. function:: $InputPTCPServerKeepAlive\_intvl The interval between subsequential keepalive probes, regardless of what the connection has exchanged in the meantime. The default, 0, means that the operating system defaults are used. This has only effect if keep-alive is enabled. The functionality may not be available on all platforms. .. function:: $InputPTCPServerKeepAlive\_time The interval between the last data packet sent (simple ACKs are not considered data) and the first keepalive probe; after the connection is marked to need keepalive, this counter is not used any further. The default, 0, means that the operating system defaults are used. This has only effect if keep-alive is enabled. The functionality may not be available on all platforms. .. function:: $InputPTCPServerRun Starts a TCP server on selected port .. function:: $InputPTCPServerInputName Sets a name for the inputname property. If no name is set "imptcp" is used by default. Setting a name is not strictly necessary, but can be useful to apply filtering based on which input the message was received from. .. function:: $InputPTCPServerBindRuleset Binds specified ruleset to next server defined. .. function:: $InputPTCPServerListenIP On multi-homed machines, specifies to which local address the next listerner should be bound. Caveats/Known Bugs ------------------ - module always binds to all interfaces Example -------- This sets up a TCP server on port 514: :: $ModLoad imptcp # needs to be done just once $InputPTCPServerRun 514